Products 1-48 of 252
Show
Availability: In Stock
Item #: 47222-S -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45500 -
Mortising Carbide Tipped 2 Flute - Cutting mortises for hinges and locks can be challenging; the mortse depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.
Availability: In Stock
Item #: 42420 -
This slightly tapered bit is specifically designed for wood patternmaking, especially wood vacuum forming molds where draft (3, 5 and 7 Degree taper) is required for releasing the styrene or other plastic from the mold. It can be used to bevel the leading edge on a door.
Availability: In Stock
Item #: DRB-416 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges. Polycrystalline Diamond (PCD) for extremely long life. Maximum recommended material depth in one pass varies from 0.5mm to 3.0mm depends on the hardness. The harder the material, the less depth.
Availability: In Stock
Item #: 45260 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45408 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 47220 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45502 -
Mortising Carbide Tipped 2 Flute - Cutting mortises for hinges and locks can be challenging; the mortse depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.
Availability: In Stock
Item #: 42422 -
This slightly tapered bit is specifically designed for wood patternmaking, especially wood vacuum forming molds where draft (3, 5 and 7 Degree taper) is required for releasing the styrene or other plastic from the mold. It can be used to bevel the leading edge on a door.
Availability: In Stock
Item #: 45624 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 46480 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45486 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 47222 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45504 -
Mortising Carbide Tipped 2 Flute - Cutting mortises for hinges and locks can be challenging; the mortse depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.
Availability: In Stock
Item #: 42424 -
This slightly tapered bit is specifically designed for wood patternmaking, especially wood vacuum forming molds where draft (3, 5 and 7 Degree taper) is required for releasing the styrene or other plastic from the mold. It can be used to bevel the leading edge on a door.
Availability: In Stock
Item #: 45705 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 45190 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45409 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 47223-S -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45181 -
Mortising Carbide Tipped 2 Flute - Cutting mortises for hinges and locks can be challenging; the mortse depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.
Availability: In Stock
Item #: 47144 -
This slightly tapered bit is specifically designed for wood patternmaking, especially wood vacuum forming molds where draft (3, 5 and 7 Degree taper) is required for releasing the styrene or other plastic from the mold. It can be used to bevel the leading edge on a door.
Availability: In Stock
Item #: 45706 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 45410 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 45191 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 47224-S -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45505 -
Mortising Carbide Tipped 2 Flute - Cutting mortises for hinges and locks can be challenging; the mortse depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.
Availability: In Stock
Item #: 45625 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 46482 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45412 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 47224 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45700 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 45192 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45413 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 45540 -
Up-Shear Bit Slot Mortiser Carbide Tipped 2 Flute - These bits are designed to do deep slot and holes for tenon, especially in doors, chairs, tables, etc. Special carbide with a 1" long up-shear and chipbreaker for fast cuts and chip clearance. For use in lock mortising and door machines. **Warning! DO NOT USE THESE BITS ON A DRILL PRESS MACHINE UNDER ANY CIRCUMSTANCES!
Availability: In Stock
Item #: 45475 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45702 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 45199 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45414 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 45542 -
Up-Shear Bit Slot Mortiser Carbide Tipped 2 Flute - These bits are designed to do deep slot and holes for tenon, especially in doors, chairs, tables, etc. Special carbide with a 1" long up-shear and chipbreaker for fast cuts and chip clearance. For use in lock mortising and door machines. **Warning! DO NOT USE THESE BITS ON A DRILL PRESS MACHINE UNDER ANY CIRCUMSTANCES!
Availability: In Stock
Item #: 47226 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: DRB-418 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges. Polycrystalline Diamond (PCD) for extremely long life. Maximum recommended material depth in one pass varies from 0.5mm to 3.0mm depends on the hardness. The Harder the material, the less depth.
Availability: In Stock
Item #: 45200 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.
Availability: In Stock
Item #: 45415 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 45544 -
Up-Shear Bit Slot Mortiser Carbide Tipped 2 Flute - These bits are designed to do deep slot and holes for tenon, especially in doors, chairs, tables, etc. Special carbide with a 1" long up-shear and chipbreaker for fast cuts and chip clearance. For use in lock mortising and door machines. **Warning! DO NOT USE THESE BITS ON A DRILL PRESS MACHINE UNDER ANY CIRCUMSTANCES!
Availability: In Stock
Item #: 45481 -
Flush Trim Plunge Template Carbide Tipped 2 & 3 Flute with Upper Ball Bearing - This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers.
Availability: In Stock
Item #: 45704 -
Cut decorative V-Grooves and lettering on signs with these bits. Use with an Edge Guide to chamfer and bevel edges.
Availability: In Stock
Item #: 45401 -
High Production Straight Plunge Carbide Tipped Router Bits AMAX extended life carbide features a 200% longer tool life, a superior geometric design and super clean cuts in wood, MDF, and plywood.
Availability: In Stock
Item #: 45201 -
High Production Straight Plunge Carbide Tipped using a two-flute bit where the finish is paramount. Two Flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.